UPGRADED! from 24″ to 50″ Table Saw Fence for my Workbench

UPGRADED! from 24″ to 50″ Table Saw Fence for my Workbench

See how I added a new 50″ table saw fence system to my Delta table saw and DIY workbench to give me precision cuts up to 50″ wide. 

Want to build your own table saw workbench like mine? See the details and plans here. 

Upgraded Table Saw Fence on My Workbench

This post contains affiliate links. Learn more and read our full disclosure policy here. 

One of the most asked questions about our table saw workbench is which fence I use on my table saw. 

table saw workbench with old Delta original fence

I have an older model Delta saw, and until now, I’ve just been using the fence that came with the saw.

When I built the workbench, that meant I had to disconnect the fence at the back to accommodate the table — and that was working just fine for cuts up to about 24″ wide.

But with a big workbench area like I have, I wanted a better fence to allow for longer cuts.

And oh boy, was this new fence an upgrade! 

I went with the Vega Utility 50 Saw Fence for a few reasons:

Note that this table saw fence system is also available in a smaller 26″ system if you prefer.

rolling table saw workbench with 50-inch table saw fence system

Installing the Table Saw Fence System

As you can see in the video, it was a pretty straightforward process to install the new Vega table saw fence system.

…Even if I did have to drill a couple extra holes a couple of times! (Be sure to pay attention to the diagrams in the instructions 😉

I was mostly able to follow the manufacturer instructions (included with the fence system and viewable here) with just a couple of adjustments to fit my saw and setup.

Like any custom precision install, the fine-tuning and adjusting to square were what took the most time. But that time ensures I get accurate cuts, so do not skimp on those adjustments!

To install the upgraded table saw fence, I used:

extra bolt setup for front rail fence attachment

Note that with the setup of my table saw workbench, I did not attach the back rail. This means I did NOT use all the parts of the system (as shown in the video and below).

How I attached the Vega table saw fence to my workbench:

Remember, since I have a wide table saw workbench surface, I did NOT install the back rail. Follow manufacturer instructions based on your installation needs.  

Step 1: Level

I needed to level my table saw workbench. I had moved garages since I first built the workbench and this new location has a floor that is much less even.

level the table saw workbench

Step 2: Remove old fence

This didn’t take long — I just removed the hardware to remove the old fence from the saw.

Step 3: Take inventory

Lay out the table saw fence pieces to determine which pieces I needed.

Remember, there is no back rail for my setup, so I showed in the video which pieces I wasn’t using in this install: the back rail, brackets, and accompanying hardware.

back rail parts NOT used for my table saw fence install

Step 4: Dry fit

Dry fit the pieces on my workbench to check fit and location.

Drill new holes in the table saw, as needed, to fit the front rail hardware.

Step 5: Attach brackets

Attach the brackets to the table saw and level. This is where I needed the extra 1/4″ x 1 1/2″ bolt, washers, and nut — but not all installs will require that.

Following the manufacturer instructions (which you can see in the product listing at Rockler), the brackets are ~1/8″ below the surface of the table saw workbench.

Step 6: Attach the front rail

Attach the front rail/bar to the brackets.

There are two sets of holes to allow for some adjustment here.

(And this is where I had to drill another hole in my table saw apron to get the placement right.)

Step 7: Assemble and attach the fence

Assemble the fence and attach it to the front rail/bar.

This step was very simple — see the process at about 5:40 in the video.

Step 8: Adjust for square

Adjust the front rail and/or fence to ensure they are square.

I made some adjustments here by adding a couple washers to get the front rail exactly square to the edge of the workbench surface, so the fence was square to the blade all along the length of the front rail.

Step 9: Secure the front rail

Attach the front rail to the table saw workbench in a couple extra spots for stability and accuracy.

I used the provided brackets, 1/4″ bolts, and some additional wood scraps to keep the rail level and secure.

Step 10: Adjust the fence

Add the furniture foot pads to the fence to allow it to slide (since I’m not attaching it to the back rail with the fence supports).

Here I needed to make a few adjustments to the rail again, so that the fence was a uniform 1/16″ to 1/8″ above the work surface.

adjusted to 1/16″ to 1/8″ clearance on the table saw fence

Step 11: Fine-tune

Measure and adjust as needed to fine-tune and ensure the fence is level, even, and zeroed with the surface of the workbench and the table saw blade.

zeroing out the table saw fence system

After all that fine tuning, I cannot WAIT to work on my next project! 

Questions? Leave a comment here or in the comments on the video.

Remodelaholic is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. Please see our full disclosure here.

About Cass

Cassity started Remodelaholic with her husband, Justin, to share their love for knocking out walls together. Since then, Remodelaholic has become a great community and resource for all those wanting to know how to make their builder-grade home BEAUTIFUL on a budget!

free email bonus

Kitchen Organization Boot Camp

Is your kitchen a zen paradise? It can be. I’ll show you how.

Kitchen Organization Boot Camp

Is your kitchen a zen paradise? It can be. I’ll show you how.

This content was originally published here.